Sikkens cetol application instructions

Cetol is much easier to maintain than varnish; a light rub-down at the beginning of the season and a refresher coat of the Marine Gloss should do the trick. If you've let things go for a couple of seasons, sand back gently, paying attention to any grey spots, apply a coat of Teak and then a coat of Gloss, and you should be ready to go. surface of the second coat of Cetol® Marine Natural Teak. Allow to dry for 24 hours. Remove excess Intergrip using a vacuum. Maintenance requirements may be increased when Intergrip is used. If high gloss finish is required, use Cetol® Marine Gloss following initial application of Cetol® Marine Natural Teak. Refer to Cetol® Marine Gloss Sikkens (akzo nobel) suggest a single base coat of Cetol 1, followed by a top coat of Cetol 23 and then an additional top coat of Cetol 23 approximately 6 months later. We apply both coats of Cetol 23 at the same time though (we don't wait 6 months). Apply the first coat of Cetol 23. wait until dry, and then apply the 2nd coat of Cetol 23. Cetol HLSe 100.20 1/3 pages November 2017 Application Data Conditions of application: Application temperature: 5-35°C. Maximum relative humidity: 85% 0800 SIKKENS (745 5367) Ph: 09 571 0023, Fax: 09 571 0022, Internet: jacjay.co.nz, Email: sales@jacjay.co.nz Points to Note A Cetol HLSe system should have a minimum dry film 2) For tannin-rich timbers, apply Sikkens Cetol® Tannin & Oil Remover according to on-pack instructions, allow to sit on the timber surface for 15 minutes before thoroughly rinsing with a pressure washer or hose. Whilst timber remains wet, apply a liberal coat of Sikkens Cetol® BL Deck & Wood Cleaner and scrub into the surface: leave for 15 Sikkens Proluxe Cetol SRD is a one coat, oil-based, transparent exterior wood finish. Sikkens Proluxe Cetol SRD was created for use on a variety of wood surfaces including siding, rails, decks, and logs. Available in a curated palette of eight wood tones. PPG Mail-In Rebate - Save Up to $100 on Sikkens Proluxe Wood Finishes from July 1-10, 2022. 360. Pack sizes. 1 quart. Paint needs. Calculate how much paint you need. For professional use only. Because of the application method required for this product, it is labeled for professional use only. This product is only for use by specialists with a license to use professional boat paint products. Former Boatswain Jerry Mertz of "Aid Our Vets" applies the first and second coats of Cetol to the teak railing on a yacht. The Wounded Warrior Mentorship Pro that for those who demand the best, Sikkens delivers. The tintable base uses pigments specifically developed for use with the Sikkens Cetol® WB SRD base only. The pigments are pre-measured in 4 oz and 16 oz bottles for in-store mixing to produce the wood finish color(s) desired. Cetol SRD WB Brochure_3-11-10.indd 2 3/18/10 1:18 PM For airless spray, use a .011"-.013" tip at 1200 - 1700 psi, adjust pressure as needed. Apply one even coat of Sikkens Log & Siding Wood Finish, avoiding heavy application. Let surface dry for minimum 24 hour period (see container). Apply second coat of Cetol Log & Siding . 6. Apply a third coat using Cetol 23 Plus 7. Clean tools with mineral spirits * For full log applications, call Sikkens Sales and Technical Support. Outdoor Furniture/Fence Applications 1. Follow the preparation procedures 2. Apply one coat of Cetol 1 3. Let surface dry a minimum of 24 hours 4. Apply second coat of Cet